Coaching & Upsell, 8 min read

DVI process for auto repair shops: the steps, and how to track it by tech and shop

A good DVI process for an auto repair shop has seven steps: set expectations at drop-off, inspect every eligible car with a template that fits the visit, take photos that explain themselves, have the advisor review before sending, send it without a cold call, follow up on what was declined, and bring it up at the next visit. Then you check that it actually happens, with five numbers by technician and by shop: completion rate, photos per inspection, recommended dollars per inspection, approval rate and time to send.

Most of what ranks for "DVI process" is written by inspection software companies or is about one shop. That's useful for picking a tool. This guide is for owners with more than one shop who need to know whether every shop runs the process the same way, without reading every inspection.

Quick answer

  • The process: expectations at drop-off, inspect, photograph, advisor review, send, follow up, next-visit check.
  • Track 5 numbers by tech and shop: DVI completion rate, photos per inspection, recommended $ per inspection, approval rate, minutes from car-in to DVI sent.
  • Completion rate comes first. A shop can't sell what nobody inspected.
  • Match inspections to cars in the bays, not only to repair orders, or cars that never got an RO stay invisible.
  • Compare each shop to its own last 3 months before comparing shops to each other.

What is a DVI process?

A digital vehicle inspection (DVI) replaces the paper inspection sheet with a tablet or phone report: each item is marked good, needs attention soon or needs attention now, with photos, video and notes, and the report goes to the customer by text or email (Autoflow). The DVI is the tool. The process is everything around it: who inspects which cars, what counts as done, who checks it before it goes out, and what happens when the customer says no.

That difference matters. Autoflow's founder puts it plainly: if the inspection process is poor, changing the tool won't change the result (Autoflow). Shops that bought DVI software and kept the old phone-call habits get the old results.

What are the steps in a DVI process?

StepWhoWhat "done" meansWhat to measure
1. Drop-offAdvisorCustomer knows an inspection is coming, roughly when, and how results will arrive% of ROs with a contact preference recorded
2. InspectTechnicianEvery eligible car gets the template that fits the visitCompletion rate
3. PhotographTechnicianEvery yellow or red item has a photo or video that shows the problem without a captionPhotos per inspection
4. ReviewAdvisorFindings checked, priced, notes in plain languageMinutes from car-in to DVI sent
5. SendAdvisorSent by the customer's chosen channel, no surprise call% sent before the car is done
6. Follow upAdvisorEvery declined item has a reason and a follow-up dateRecapture rate on declined work
7. Next visitAdvisorOpen items raised at check-in% of returning cars with open items reviewed

Step 1 is the one shops skip. A 2023 review of 100+ shops by AutoTechIQ found that customers often drop off without knowing the scope or timing of the inspection, and then get an unexpected call mid-day that puts them on the defensive (MOTOR). Telling them at the counter what's coming, and when, changes how the report is read.

Step 2 is where templates matter. One shop owner told Ratchet+Wrench his single, long inspection list had techs skipping sections and customers waiting up to four hours for what should have been a 90-minute inspection. He split it into three tiers by vehicle mileage, built around the order techs actually work on the car (Ratchet+Wrench). One shop, but the lesson travels: a template techs can finish is a template they'll use.

What should "DVI completed" mean?

Write it down, the same at every shop, or each shop will define it its own way. A workable definition:

  • The inspection was started on the vehicle that's in the bay, not marked complete from the counter.
  • Every template item has a status.
  • Every yellow and red item has at least one photo or video.
  • The report was sent to the customer, or the reason it wasn't is logged (customer declined inspection, fleet account that doesn't get one).

"Eligible" needs the same treatment. Decide which visits get a full inspection, which get a short one and which get none (a tire swap on a car inspected last week, say). Otherwise a shop with lots of quick jobs will look worse than it is.

How do you track DVI completion by technician and by shop?

Autoflow suggests three numbers per tech: completion rate on eligible vehicles, average photos and line items per inspection, and ARO on cars with a full DVI versus without (Autoflow). For more than one shop, add the advisor side and put them in rates so a busy shop and a quiet one can sit side by side.

NumberFormulaWhat it tells you
Completion rateCompleted DVIs ÷ eligible carsWhether the inspection happens at all
Photos per inspectionPhotos and videos ÷ completed DVIsWhether the tech shows the customer what they found
Recommended $ per inspectionRecommended $ ÷ completed DVIsWhether findings get written up and priced
Approval rateApproved $ ÷ recommended $How the advisor presents it
Time to sendMedian minutes from car-in to DVI sentWhether results reach the customer while they can still say yes today

Run the first three by technician and the last two by advisor. Then roll each up to the shop.

Worked example: three shops, one month

(Made-up numbers, not real store data.)

ShopEligible carsDVIs completedCompletionPhotos per DVIRecommended $ per DVIApprovalTime to send
A52049495%9$31038%42 min
B46032270%11$34041%55 min
C50047094%3$12062%95 min

How to read it:

  • Shop B does good inspections on the cars it inspects, but 138 eligible cars got none. At its own $340 per DVI, that's about $46,900 of work that was never even recommended. That's the biggest gap of the three, and it's a scheduling and habit problem, not a sales problem.
  • Shop C completes almost everything but averages 3 photos and $120 recommended per inspection, and takes over an hour and a half to send. A high approval rate on very little recommended work usually means quick, thin inspections. Look at a few of its DVIs side by side with Shop A's.
  • Shop A is the template for the other two. Its approval rate is the lowest, which is fine: it recommends the most and gets results out fastest.

Then run the same table for each tech inside a shop. The pattern to look for is a tech whose completion rate is high and whose photos per DVI keep falling.

What can't the DVI report show you?

The DVI software only knows about inspections that were started. It can't see a car that was in a bay all morning with no RO opened, so no inspection was ever expected. It can't tell you whether a "completed" inspection was done with the car on the lift or tapped through at the counter, or whether photos were reused from the last visit.

That's where the cameras you already have help. Counting the cars that went through each bay and matching them to ROs and DVIs each morning shows the cars that should have had an inspection and didn't, by shop and by bay. You get to know what's happening at every store without standing in it. We cover the matching method in unbilled work in auto repair shops and what fixed cameras can and can't measure in bay camera analytics.

How do you get techs to do the DVI on every car?

  • Fix the template first. If it takes too long, techs will skip parts. Tiers by mileage or visit type keep it short.
  • Make it part of the job, in writing. Autoflow points to unclear expectations as a common reason techs push back; if inspections were never part of the job description, they read as optional (Autoflow).
  • Show techs their own numbers weekly, completion and photos per DVI, next to the shop's. Keep it private to the tech and the manager.
  • Pay attention to flat-rate time. A required inspection on a flat-rate job is unpaid time unless you account for it. Decide how, and say so.
  • Have the advisor close the loop. When a tech's photo sells a job, tell them.

Common mistakes

  • Counting DVIs against ROs only. Cars without an RO never show up as missed.
  • Judging advisors on approval rate alone. It rewards recommending less.
  • One long template for every visit. It slows the bay and gets skipped.
  • Calling before the report is sent. Send it, then answer questions.
  • Comparing shops on dollars. Use rates, and each shop's own last three months.

How Trilix fits

We build the reporting so nobody pulls this by hand. Inspection data from your shop system, car counts from the bay cameras you already have and repair orders land on one owner dashboard, by shop, tech and advisor, every morning. Once the numbers point at a tech or advisor, our service advisor coaching and declined work follow-up guides cover what to do next. More on repair shops on our tire and auto repair page.

Want DVI completion by tech and shop on one screen?

We'll look at your shop system, your inspections and your cameras and show you what the report would flag at each location.

FAQ

Something else on your mind? Ask us directly or call 416-262-2723.

What is a good DVI completion rate?

There isn't a reliable industry figure, and it depends on which visits you count as eligible. Define eligible the same way at every shop, measure each shop for three months, and work up from its own baseline. Most of the value is in finding the shop or tech well below the others.

How do you measure DVI completion by technician?

Each week, per tech: completed DVIs divided by eligible cars they worked on, plus photos per inspection and recommended dollars per inspection. Completion alone can be gamed with quick, thin inspections, so read the three together.

Should every car get a DVI?

Every eligible car should, and you decide what eligible means. Many shops use tiers: a short check on low-mileage or quick visits and a full inspection on others. Write the rule down so every shop follows the same one.

How long should a DVI take?

It depends on the template and the vehicle. What matters for the customer is time from drop-off to the report arriving, so track minutes from car-in to DVI sent by shop and advisor, and shorten the template if it's slowing the bay.

Can cameras check whether a DVI was done?

They can show which cars were in which bay and for how long, and that can be matched to repair orders and inspections. That catches cars that never got an inspection at all. They don't replace the inspection or judge its quality; a manager reviewing a few DVIs a week still does that.